Short answer
The abbreviation
The Craft Yarn Council's knitting abbreviations list reads: k2tog is "knit 2 stitches together; single right-leaning decrease". The general shorthand in its pattern guide is that "Dec" means decrease, which eliminates one or more stitches, and "Tog" means together, which is working 2 or more stitches together to form a decrease. The guide adds that the most basic decrease is to work two stitches together as one.
The decreases that lean the other way
The same list gives the left-leaning decreases too, and the pattern guide says the pattern usually specifies which decrease to use because the choice changes the look:
| Abbreviation | Meaning in the list | Lean |
|---|---|---|
| k2tog | knit 2 stitches together | Right |
| ssk | slip 2 stitches knitwise, knit these 2 stitches together through back loops | Left |
| skp | slip 1 knitwise, knit 1, pass slip stitch over knit stitch | Left |
| p2tog | purl 2 stitches together | Single decrease, lean not stated |
The pattern guide says different ways of increasing and decreasing change the way the project will look, so usually the pattern tells you which to use. If your pattern only says "dec", look for instructions before choosing one.
The matching increases
For comparison, the list shows kfb as "knit 1 into front and back of a stitch; single knit increase" and m1 as "make one stitch knitwise; single knit increase".
How many stitches you lose
Each k2tog, ssk or skp uses two stitches and leaves one, so each decrease reduces your count by 1. A row with six decreases ends with six fewer stitches than it started with, which is easy to check against the count your pattern gives for the end of the row.
Take a row of 30 stitches that says "[k3, k2tog] 6 times". Each bracket uses 5 stitches and leaves 4, so six repeats use 30 stitches and leave 24. The guide explains the bracket format with its own example: "[YO, K2tog] 6 times means you will YO, then knit 2 sts together", repeated six times. The 30-to-24 count is our own arithmetic using the same format, not a pattern from the source.
Work even and reading the instruction
The guide defines "Work even" as continuing what you have been doing, without any increases or decreases. It also explains "maintain pattern as established": you keep the center part in the stitch pattern as you already set it up while increasing or decreasing at the edges. For shaped pieces such as a front, it says the decreases on one side are reversed for the other, for example armhole decreases on a left front are worked at the beginning of right side rows, and on the right front at the end.
When the pattern says decrease evenly
Some patterns just say to decrease a number of stitches evenly across a row, without telling you where. Because every decrease uses two stitches, the spacing sum is different from an increase. Our increase and decrease evenly calculator writes the plan as a pattern line using k2tog for knitting, and you can swap in ssk or another decrease if you prefer. For the arithmetic of the increase case, see how to increase evenly across a row in knitting.
Keeping your place in a decrease row
The practical problem with k2tog is that the repeats are short and easy to lose track of mid-row. A repeat counter, or a pencil mark per repeat, helps. See how to keep track of rows in knitting and what rep from asterisk means.
Counts rows and stitches for knitting and crochet projects, with linked counters and per-row notes.
Get it on Google PlayFree, with one small banner ad on the project list and project details, never on the counter screen. A one-time Craft Pass removes the ads and adds unlimited projects and the full finished-project archive.
Row Counter is a full-screen tap counter for knitting and crochet. You set a row counter and a repeat counter that ticks up each time a pattern repeat completes, and you can pin notes to specific rows, such as the lean of the decrease you want on that row. It is not a pattern library or chart reader and does not teach the stitches themselves.