Skip to content

How to Square a Corner with the 3-4-5 Rule

In this guide
  1. Why it works
  2. The steps (sources read on 16 November 2026)
  3. Use a bigger triangle
  4. Check a whole rectangle with the diagonals
  5. How accurate does it need to be
  6. Common mistakes

Short answer

Measure 3 units along one side from the corner and 4 units along the other, then measure the diagonal between the two marks. If it reads exactly 5 units, the corner is square. If it is short or long, move one side in or out and measure again. For bigger layouts use a bigger multiple of the same triangle, such as 6-8-10 or 9-12-15.

Why it works

A triangle with sides of 3, 4 and 5 has a 90 degree angle opposite the 5 side. The sums confirm it: 3 x 3 + 4 x 4 = 9 + 16 = 25, and 5 x 5 = 25. This is the Pythagorean relationship, and any units work, as long as all three numbers use the same unit.

The steps (sources read on 16 November 2026)

  1. Pick the corner. Treat one corner as your home base and use the same edge of each member for every measurement. If you measure from the inside face of one board, measure from the inside face of the others. Mixing inside and outside edges can throw the result off by about the thickness of the lumber, which InspectApedia puts at 1 1/2 inches for framing lumber.
  2. Mark 3 units along the first side from the corner.
  3. Mark 4 units along the side that should be at a right angle, from the same corner.
  4. Measure the diagonal between the two marks. InspectApedia says when the diagonal equals 5 feet, the framing around that corner is square.
  5. Adjust. If the diagonal is off, move the free side in or out, usually just one of the two legs, and measure again until it reads 5.
  6. Keep the tape level. A diagonal that is not level reads longer than the true distance and skews the result.

Use a bigger triangle

Both sources recommend scaling up. A Concord Carpenter notes that for large layouts a framing square is too small to guarantee the accuracy needed, and that any multiple of the 3-4-5 rule can be used. InspectApedia advises using the largest square-up triangle that fits on the structure.

Multiply all three numbers by the same factor:

MultipleSide ASide BDiagonal
x 1345
x 26810
x 391215
x 4121620
x 5152025

In metric, 0.6 m, 0.8 m and 1.0 m is the x 0.2 version, and 3 m, 4 m and 5 m is a convenient size for a small building. The sources give their examples in feet, but the ratio is the same in any unit. Our reading of the sources is that a longer triangle makes a small marking error matter less, because the same error is spread over a longer distance. That reasoning is our own interpretation.

Check a whole rectangle with the diagonals

For a full rectangle there is a second check. InspectApedia says to measure both diagonals, and if they are identical, the corners are square. First confirm that opposite sides are parallel and equal in length, since a trapezoid can also produce unequal diagonals. Use the 3-4-5 rule on each corner, and the diagonals as a final check on the whole layout.

How accurate does it need to be

Neither page gives a numeric tolerance. Their standard is an exact result, a 5 unit diagonal, or equal diagonals. InspectApedia explains why it matters: errors at the base of a deck, house or porch continue to grow and compound as the building goes up. If a project has a specified tolerance, follow the plans or your local requirements.

Common mistakes

  • Measuring the three sides from different edges of the boards.
  • Using a short triangle on a long wall.
  • Sagging the tape over a long diagonal.
  • Squaring one corner and assuming the others are fine. Check every corner, or the diagonals.

Construction Calc

Works out material quantities and measurements for building jobs, metric first with an imperial mode.

Get it on Google Play

Free with a small banner ad and an occasional full-screen ad after you save. Every calculator is free. A one-time Pro unlock removes the ads, allows unlimited saved jobs, and lets you send a job's materials list to WhatsApp, SMS or email. There is no subscription.

Construction Calc has ten calculators, including a right angle calculator, area and volume, and a concrete calculator, with metric input where you choose mm, cm or m explicitly. You can save results to a named job as you work through a site. It does not replace a tape and a second person on the other end.

Sources

  1. Deck Square Up - InspectApedia
  2. The 3-4-5 Method For Squaring Corners - A Concord Carpenter

Search the site